高清不卡一区二区三区,国产区日韩精品久久无码,苍井空亚洲无码在线看,亚洲国产综合精品2020

你在找什么？

0.96英寸64x128垂直O(jiān)LED顯示屏，帶SH1107 IC、13針、4線串行接口、I2C

SCE096013-V01是具有COG類型、64x128分辨率、SH1107 IC、4線串行接口、I2C、13針的垂直O(jiān)LED顯示器

型號:
SCE096013-V01
Size (inch)尺寸（英寸）:
0.96寸
Resolution:
64×128
Outline Dimension (mm):
14×28×1.227
Viewing Area (mm):
11.86×22.74
Active Area (mm):
10.86×21.74
Interface:
I2C/ 4-wire SPI
IC Part No.:
SH1107
Color:
Monochrome (White)
PIN:
13
FPC type:
Soldering

立即查詢

產(chǎn)品詳細(xì)信息

Basic Information

Display Color:               White
Dot Matrix:                    64X128
Drive IC:                        SH1107
Viewing Angle:              160°

Aperture rate:    78%
Interface:                       4wire serial interface, I2C
Outline Dimension:        14.0(W)x28.0(H)x1.227(D)
View area:                      11.86 (W) x 22.74(H)
PIN:                                13
FPC Type:                      Soldering

Drawing

General Specification

ITEM	SPECIFICATIONS	UNIT
MODULE SIZE	14.0(W)x28.0(H)x1.227(D)	mm
VIEWING AREA	11.86 (W) x 22.74(H)	mm
ACTIVE AREA	10.86 (W) x 21.74(H)	mm
DOT SIZE	0.15(W) x0.15(H)	mm
DOT PITCH	0.17(W) x0.17 (H)	mm
ASSY.TYPE	COG	---
WEIGHT	TBD

Interface Definition

PIN NO.	SYMBOL	TYPE	FUNCTION DESCRIPTIONS
1	NC		NC
2	VPP	P	Power supply for OLED driving voltage. This is the most positive voltage supply pad of the chip. It should be supplied externally.
3	VCOMH	O	This is a pad for the voltage output high level for common signals. A capacitor should be connected between this pad and VSS.
4	VDD	P	Power pin for logic circuit. It must be connected to external source.
5	IM1	I	Interface selection pins.
6	IREF	I	Current reference for brightness adjustment. This is segment output current reference pin. A resistor should be connected between this pin and VSS . Set the current at 15.625 uA maximum.
7	CS	I	Chip Select input pin. Active "L"
8	RES	I	Hardware reset input pin. Active "L".
9	A0	I	This pin is Data/Command control pin. When the pin is pulled HIGH, the data at D[7:0] is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
10	D0	I/O	When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA).
11	D1	I/O
12	VSS	P	Ground pin. It must be connected to external ground.
13	NC		NC